Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
Hello
SDK starts adverting when reset. I want to start adverting at the push of a button.
SDK version : 17.0.0
SWDevide : s112
When the button is pressed as above...
Hi everyone,
I want to send large data with https protocol.
I edited the https_client sample split the data and looped send() for sending the large data.
But when...
Hi all
I have an issue regarding central- peripheral connection.( using nRF52832)
In the past I developed a peripheral device using SDK 11.
In order to manufacture it...
Hello, I am doing a bachelor thesis using the nRF52 Development Kit to control a (RC ) car, and I am 3D-printing holders for extra peripherals. During the 3D-modeling and...
When I run nrfjprog --pinreset it says "Applying pin reset" but it has no effect on the connected nRF52832, it just continues running. Other nrfjprog operations like reading...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hello,
I am trying to get reliable log output using the Nordic Connect SDK (NCS) over RTT. When I use Minimal mode, the following config:
CONFIG_LOG_MODE_MINIMAL=y CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL...
Hi All,
Sorry for such a very basic question, but I've tried many things and combinations and cannot make this work.
I'm trying to discover BLE sensors using nrf_ble_scan_init...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
