I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello!
I would like to know the gain of the integrated PCB antenna on the nRF52832 chip. Is there a documentation paper on the antenna itself? I couldnt find any info...
Hi!
I am evaluating DFU over Mesh by following the configuration guide here Configuring and performing DFU over Mesh . I am trying to prepare a package with the application...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I have a question about setting the UUID. My program has one advertised UUID...
I am using slightly modified master SPI example from here which is running on nRF5340 to communicate with slave device, which is RHD2216 . SPI frequency is NRF_SPIM_FREQ_4M...
Using a nRF52832, I would like to broadcast advertisement packets normally and in extended mode at the same time. Is this possible or do I have to ping-pong between, stop...
ok,i recenlty have gotten iq samples from Rx.but i think my received iq samples are from Tx .i use the NCS 1.9.1 with two boards nrf52833dk.
firstly,i connect antenna array...
Hi, I have already updated all certificates and firmware. But when I am trying to connect my device to the cloud it does not recognize my device. when I am trying to add my...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte in mode NB-IoT not in LTE-M?
Can we say that every time a data is sent, it takes 950...
Hello, All
I received following message when I test the code, it appears on both sides,
ASSERTION FAIL [chunk_used(h, c)] @ WEST_TOPDIR/zephyr/lib/os/heap.c :163
unexpected...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
I am after some assistance with creating a 6 layer stackup to use with the NRF52840_CIAA that is 1.6mm thick.
Can you provide recommend layer stack up that have been...
Hello.
Is there any difference between i2s hardware in nRF52840 and nRF52833? I made WS2812B i2s driver and working very good on nRF52840. The same code (project is adjusted...
Hi, I'm developing an application which is merging from (ble_app_uart + libuarte + app_timer + pwm). Here is my main.c Now I'm developing an feature that using timer ((app_timer...
I'm trying to use parity UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_PARITY_NONE...
