I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I'm using the saadc and I notice that the max value that saadc can convert is 3,3V. If I try to convert an higher value, the result has no sense. For my project, I need...
Currently I am working on a open thread project.
Right now I am facing an issue in which my board/code is getting reset every time after I have done some changes in my previous...
Hello,
Currently In customized PCB board, nRF52832 is connected to both HFCLK(32MHz) and LFCLK(32MHz).
It takes up too much space. So HW engineer asked me to consider...
Hello. I have a device that connects to desktop app through usbuart-to-ble converter and I'm trying to simulate it using nrf52832. I've started from ble_blinky example using...
Dear,
Based on the material ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf5340%2Fqspi.html ), Encryption should be enabled independently for XIP and EasyDMA...
I want to use mcuboot together with LittleFS/NVS and a custom partition foo with my own flash storage routines. It works as long CONFIG_BOOTLOADER_MCUBOOT= n.
But with CONFIG_BOOTLOADER_MCUBOOT...
Hello,
I just received an nRF21540 EK, I am trying to use it on my current hardware which is only for scanning beacons (won't transmit) so need use it as LNA in the received...
Hi everyone. I have to turn off the bluetooth module to save battery. I am using the SDK example "ble_app_template_pca10056_s140". To start the advertisement I use the "ble_advertising_start...
project set up: Development board used nrf52832 ,SDK 15.0 ,SEGGER 5.10
actually i want to read data string from ESP32 using nrf52832 via UART (RX,TX) and send it to nrf...
Hello All,
We are using Power Profilier Kit 2 for measuring the current consumption of our device.
We Start the measurement at 14:16 PM. after 1 hour and 39 minutes (at...
HI,
we are working with
nRF5 SDK v15.2.0 ------------------------ Release Date: Week 37, 2018
Our use-case has a central device, which has 7 to 10 peripheral connected...
Hello,
We are using nRF Connect SDK 1.8.0 with nRF52832. As per the nRF Connect Documentation, when there is no active task, idle thread is called. Could you let us know...
Good morning,
I' mi trying to improve power saving on a device and it would be great to trigger:
1.an NRF52832 input pin transition triggers a "SPI1 instance" reading...
