I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi.
Setup:
I use NRF5340. Open project from SES menu "Open nRF Connect SDK project".
nRF Connect SDK Release: 1.4.99-dev1. nRF Connect Toolchain Version: 1.4.0.
Project...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. I have a few questions about the source code: 1. Looking at recv(), connected() and disconnected() functions, seems...
All nRF5340 reference designs use via-in-pad structure. Instead e.g. nRF52840 has reference designs which can be used with through hole PCB.
nRF5340 seem to have 19 IO's...
Hi,
I'm trying to do a very simple thing - setting those pins as high or low,
but I see that it simply does not work for those pins, I see no change in led state that...
Hi everyone,
I'm developing on nrf9160DK. I would like to know if there is any difference between setting the APN through the CONFIG_PDN_DEFAULT_APN in prj.conf file or...
I am using the SLM app from the 1.9.1 SDK.
I connect to my MQTT broker using TLS offloaded on the modem. I subscribe to a topic using QoS = 1 Then if a message is published...
I have been trying to get mqtt to stay connected without activity for more than 30 minutes. any keepalive value over 30 minutes just results in mqtt discoonection. tried with...
On a custom board, I've got 2 inputs connected to an external pullup and a pad. One in is P12, one on P21.
When I short the pad for P12 with GND, that input read low, that...
Hi,
I tried to access Nordic devzone, yesterday and today, but got an error message that "the page cannot be displayed because of an internal server error has occurred...
Hello everyone!
I am trying to figure out how SPI drivers for Bosch bme280 sensor work... I would like to somehow recycle them to write my own SPI drivers for another device...
Hi Nordic,
Using nrf-connect 1.9.99 and Zephyr 2.7.99 (*** Booting Zephyr OS build v2.7.99-ncs1-1 ***)
I am using then nRF9160-DK and everything is fine. Getting 40uA...
I'm running Manjaro Linux and have ran through the installation instructions for the nRF Connect Desktop. I have separately downloaded the Segger JLink software as instructed...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hello, I am using 52832. There is an external interrupt count with a maximum frequency of 1kHz. I have two hardware. One I transmit to the mobile phone at an interval of 50ms...
Hello sir ,
i am trying to build file from given sample code file name is "azure_iot_hub" , i don't make any changes in this file .
on adding build configuration it show...
