[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am attempting to upgrade from nRF Connect SDK version 1.7 to version 1.9.1
My application is using the nrf52840 on a custom board.
I'm using Zephyr and created a board...
Hi,
currently I'm testing several options to transfer data in broadcast manner, i.e. in fact extended advertising due to the amount of data to transmit. A few days ago,...
Hallo,
I am starting to develop an application using nrf5340 SoC. I have got two Audio DK and would like to begin my development using nRF Connect SDK.
However, I was...
Hi,
With the nRF5340 DK boards (PCA10095), there are 3 VCOM ports (as viewed in VS Code) - printk debug logs for the app core are transmitted on VCOM2. However, the nRF5340...
I was trying to schedule a work item when a struct k_poll_signal is raised by an interrupt, but was unable to get the work to happen. I could tell that the k_work_poll_submit...
Hi, I'm new to this and I was just wondering, since I'm still learning and successfully coded my first app, I'm asking how can you flash / burn / build & run SMD component...
yes, i meet a problem.i notice that isp have done a AOA demo based on Nordic board.
but i use it to get the angle.i find i can't use it.what is this problem?
I am running a nrf52dk_nrf52832 build with SDK v1.9.1. A week ago I was building my project and everything was working fine. Then, my program stopped being flashed - I could...
Hello!
I'm working with nRF9160 on a custom board and I'm trying to use SUPL to improve time to first fix, I'm following the sample nrf9160/gnss/src/assistance_supl.c. I...
I am testing the Asset_tracker_v2 application on thingy-91. I took the SIM card out so the device goes into the boot loop.
The on_state_init () function has the condition...
i am able to succesfully build and flash the simple "hello world" example using segger embedded studio and programmer app.
finding difficulty in logs checking because, the...
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M.
To recreate: build /zephyr/samples/fs/littleFS and set target...
I'd like to test the SPI communication between my nRF52833 DK and a ICM-20948 developer board. Keep in mind that the ICM -21948 is a device not listed in the NCS. To activate...
Hi, Nordicsemi,
We found one of Mesh device in our customer did not recievie and transmit Mesh package any more. try Nrf-connect application to scan and found the device...
