Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
I have used the kit for weeks now measuring the power consumption of my custom hardware with the external hardware setup [1].
Suddenly the sleep currents of my target...
Hi,
I got an error BLE_ERROR_INVALID_CONN_HANDLE at the function sd_ble_gap_disconnect. I know that this error has to do with the fact that an invalid connection handle...
I have developed a code based on app_timer to initiate an interrupt every 10 seconds. Inside app_timer_handler, I have code for reading data from an I2C device.
When I run...
Hi,
I use ncs 1.9.1, and the MCU is nRF5340.
After run the timeslot some minitus, a error occurred.
mpsl_init: MPSL ASSERT: 112, 2236.
what the error mean?
Hi,
As a part of proof of concept for our newest design We have tried to setup USB CDC using nRF52840DK and NCS 1.9. In order to quickly test things out We have tried...
As a test of nrf9160 DK board, I am trying to read a voltage signal and report it to the nRF cloud. My original plan is to change a bit of the Asset Tracking sample code and...
Hi everyone,
I was wondering if there is any method that I can use to test my development kit's scanning/discovering capabilities.
For example, in Bluetooth Advertising...
Dear ,
I use nRF52833 to transfer audio,but I found that this audio will delay 130ms.
I didn't use 32.768K low frequency crystal, do you think this will affect delay time...
Hello there,
I'm trying to connect to the AWS cloud. However, when I attempt to connect, it gives out error 128. Which, accoring to this table, means there's no connected...
Hello!
Quick question: When a device is connected to the u.FL port (actively transmitting things to the port) on the nrf52840 board, does board (in rx mode) only listen...
hi,
program: 'ble_app_blinky_pca10056-s140'
nRF 52840 dk
keil uvision5 IDE.
with the help of IDE , i could build the code and flash the code on to the board.
but...
Hello
I'm testing nrf52820 longrange speed, but it's faster than my calculations. Will it automatically turn on the fec?
This is my config below.
m_adv_params . primary_phy...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
Sometimes when i disconnect ble from mobile application and again connect then i...
Hello.
I'm using nRF52833, pca10100.
Can I erase only 16 bytes (or more..)?
I read this explaination , and t here's an erase page partial register, but I don't know...
Hello!
I'm currently working on an IoT device that is supposed to send data to the cloud using MQTT with a TLS layer. We got this working in Norway using LTE-M and the...
