SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hello, I'm in the process of attempting to implement Eddystone EID on the nRF52805.
It's been a bit of a nightmare, so I'm finally taking the bold step to make my first...
I am using SDK 17.1.0 with an nRF52832 design similar to the P10040.
I was previously using the original timer application and things were looking good. I decided to upgrade...
Hi,
1. Please provide me with an example in which UART0, UART1, uart2, and uART3 are enabled
2. The sending and receiving rate of each UART must reach 1,000,000 baud rate...
We are porting a project from SDK 11 to nrf5 SDK 17.0.2. We have also used a couple of different versions of SDK 15 extensively on several different products.
Our code...
SDK: NCS 2.0.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF5340
IDE: VS Code
Hi Everyone,
I am porting an existing project based...
Hello All,
We are intending to start a new project using nRF52840 SOC, for the same i decided to work with nRF connect SDK as it is recommended by nordic,
I am new to...
When connecting to AWS IOT the Asset Tracker V2 uses MQTT to AWS-IOT. This is TLS 1.2 from what I understand. We are using the 1.8 skd / 1.3.1 modem firmware.
We have...
Hi everyone
We have developed a smartwatch with a nrf9160 chip. We have used nrf Connect SDK 1.2 for the development process.
Now we want to migrate our project to nrf...
Hello there,
I am using the peripheral/radio/transmitter and receiver example in SDK17
But I am only able to transmit 2 bytes. I want to transmit like 8 or 9 bytes...
Hi,
I am testing FOTA function using sample "http_update/application_update" on NRF9160DK.
But found that the system boot stuck at
I had tested this sample with...
HI
I am using this sequence functions in my main loop for low current consumption
__SEV(); __WFE(); __WFE();
normally I have 13mA in my application when I am using...
nrf5-sdk v16.0.0
If you use the nrf_ble_scan module to try and connect to a peripheral that emits both connectable and non-connectable advertising packets, the module does...
Hello !
From PS it is not always clear what RADIO registers/fields are relevant for Ieee802154_250Kbit radio mode and must be initialized.
For example CRCINC ?
On "Figure...
Hi team,
I'm making BT low power keyboard using nRF52832 DV kit and with Zephyr RTOS. For this which IDE is best OR comfortable?
But I'm not getting example code if anyone...
I am programming an external device with the same code loaded onto the nRF5 DK. The sample works on the DK, It broadcasts and I can connect. However, when I program an external...
