I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I've created a new sandbox project for a nRF9160DK that requires a SPI Master for testing a Flash part. Since I already have "working" SPIM code in a different Segger project...
I am using the beacon mod example with my nRF52-DK to calc battery life. All measurements are taken with PPK2 (a great tool by the way), but in the PC application my timestamp...
Is there a process in place for updating a controller only build via the HCI? My current set up is a 9160 as the BLE Host, a 52820 as the BLE controller, MCUs are connected...
Hello, Im a little confused about the nRF Connect SDK ecosystem.
Currently Im using SES with cloned nRF SDK 15.0.3 for nrf52811, however I would like to start using https...
Hi
I plan to enable hardware flow control in the coprocessor code. After successful compilation and burning, I will use Ubuntu to start wpantund and an error will be reported...
We already made working code with NRF5 SDK. It has added three characteristics to send data via UART from a MCU. Each characteristics for separate purposes, for eg. Characteristics1...
Hello,
I'm selecting crystals for a project with nRF52832QFAA.
I noticed that on the spec the drive levels of HFXO and LFXO are 100uW and 1uW respectively. Should the...
Hi,
I'm trying to integrate https://github.com/nrfconnect/sdk-nrf in version v1.9.1 in my baremetal application (nRF5340 NET and APP CPUs). Where can I find the startup...
Hi,
we are using an nRF52833 for an application where we have a sensors, a USB interface and an SD memory device.
We would like to write and read back sensor values to...
Hi,
I am following the step by step tutorial " Getting Started with Secure DFU Bootloader Step by Step guide "
Before following the above guide I compiled ble_app_blinky...
Hello,
I'm trying to use the VL53L1X Time of Flight sensor on my nRF52DK, but I experience some problems.
Previously, I've successfully used the VL53L1X with an Arduino...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
Hello!
I am currently working on doing the smp_svr sample:
I have done these commands so far (on created from sample application):
west build -b nrf52dk_nrf52832 -d...
Hello DevZone,
I am using Segger embedded studio with multiple build configurations for the two chips and I am having some issues to get the program to compile my nRF52810...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
