Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
Hi support,
I'm currently having issue trying to program a nrf52833 device using Jlink mini on mac. I have no problem programming the device using a pro Jlink on windows...
Hi,
I'm trying to use examples. The ICM42605 example does not work.
I get the following errors.
There seems to be an error in the code below.
It was tested with...
Hello !
I have found that error free decryption ( MIC error) on fly depends from S1LEN configuration value.
S1LEN have valid range value for each radio mode
2Mbit 1...
I'm getting an occasional NRF_LIBUARTE_ASYNC_EVT_OVERRUN_ERROR, it often takes over 24 hours to reproduce, and the libuarte appears to be generating garbage after the error...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
Hi,
Since adding a custom board to a app from a sample, the Flash button:
Has stopped working properly.
When i press it, a build is initiated, but the flash does not...
Hi,
I used this example to develop code for a low power delay function. This code uses RTC1 with frequency = 32Hz to create an interrupt every 5 seconds and event handler...
Hi,
I have been programming my custom board using SWD on a DK. It worked fine when I tried blinky example, however, when I tried nrf_ble_uart example, it stopped at the...
The documentation on how the nrf mesh app adk works is impossible to follow and understand for a junior dev like me to make something close to a working app.
I might be...
Hei!
Mid code development my ability to flash new versions went away. The only clue I have is that W11 installed some new drivers, but I'm grasping at straws. I have screwed...
