I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I currently am working on a BLE device in which I am trying to set the Service and Characteristic UUIDs. Here is an example of what I mean:
As can be seen here, the Service...
Hi, I have developed a firmware in which I have added the custom service. My custom service UUID is showing 00001400-0000-0000-0000-00000000fff0 but I want only 0xFFF0. I...
Hi there,
I'm in the midst of migrating between SDK14.2->15.2, and SD 5.1->6.1
I'm calling sd_flash_write() and sd_flash_page_erase() before enabling the SoftDevice with...
Hi,
I start a new design using the nRF Connect Sdk instead of the nRF5 Mesh Sdk.
Is it possible to provision a device over the mesh network using the NCS (like the PB...
After LPN publishes message, NRF_MESH_EVT_LPN_FRIEND_POLL_COMPLETE event is generated five times. Also I noticed that instead of transmitting single publication message LPN...
Hi,
We have a problem with a nrf9160 connected in NB-IOT with a bad signal.
During the debugging session to try to figure out what happen, we saw that the mqtt_evt_handler...
Hi everyone,
I have a problem since a couple of day with an interrupt of app_timer not triggering when adding a BLE central to my project. The device is working well as...
If I can get time through WiFi then send it to the nRF5340 and place it in a Struct TM. is there any method to have the nRF5340 maintain the time/calendar from that initial...
I'm sorry. This must be trivial to all of you. I'm a beginner with nrf52 programming, and I saw several examples that refer to timers TASK_START, TASK_CLEAR, TASK_STOP. Everywhere...
Our device has both a 9160 and a 52840 on it.
The 9160 is running the stock serial modem firmware on it.
The 52840 is running a custom handler for AT connection targeted...
Hello,
We are doing some network quality tests on LTE-M with PSM off and notice loss on UDP between 0% to sometimes 15% on simple udp messages sent every 10 seconds from...
It is not very clean to start a work_q with no name when all others name them properly, or at least put in the name of their k_work_q struct. Working with system threads it...
Hi,
I'm upgrading my firmware from sdk1.7.0 and there is one error that i can't solve and need your help.
The code is working on SDK1.7.0, solved all the errors that appeared...
Hi,
I have a nrf5340 device which is built with nrf Connect SDK 1.6. I can successfully DFU over ble by nRF Connect mobile app. Right now, I am trying to do DFU from my...
Hello,
I am attempting to configure a project with full zephyr logs (using RTT backend). I am, however, unable to get the full logs (see example below):
[00013022] <dbg...
