I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
1: The Apple's "Find my function" , How big is the "Find my SDK" ,RAM? ROM?
We can use nrf52820, or nrf52811,or nrf52810 to develop?
We must use nrf52832 to develop Apple...
Hi Nordic Magicians,
I have a couple of general questions when it comes to sending large amounts of data (FAST). Ultimately, I'm looking to transmit data with a throughput...
Hi,
I'm putting together some firmware that takes packets received over SPI and then streams them over BLE. I'm trying to run the BLE at close to 1Mb/s (which is still...
Background:
Custom boards
SDK 15.2.0
SoftDevice: s140_nrf52_6.1.0
Please see previous post / case that was closed and cannot be reopened: https://devzone.nordicsemi...
Hello,
I am using zephyr on a nRF52840 to communicate with a vl53l5cx TOF sensor using I2C. When I use i2c_reg_read_byte() or i2c_burst_read(), the device address is sent...
Does anyone know why I am getting low outliers on battery measurements with the SAADC? I am measuring the battery directly every minute. Every seven minutes consistently,...
HI,
To ensure NRF5340 2.4G rf consistency during mass production, which scheme do you suggest is more suitable （ X2 = 32MHZ 10ppm ）:
1、Offset capacitance C36 C37 placed...
I used Modem firmware version 1.3.1
In order to connect the nrf9160 DK to the AWS cloud, I am encountering errors such as AWS_ IOT_ EVT _CONNECTING, when it should be AWS_...
In a nrf52840 project using Zephyr 3.0 following Zephyr drivers are used:
the modbus serial driver(RTU mode) which uses uart1 in interrupt mode
the lora-mac driver which...
Hi,
I'm using app_ble_uart example using nrf52810 for nrf52810 UART RX & TX pins are (P0.15 - P0.14) while configuring using i got a problem with RX transmission ,when i...
Hi,
I am working on a multiple custom models, wherein I need one model to extend the functionality of another model.
I was analyzing through nCS provided "Chat" sample...
We have relatively big model composition, and reading it via nRF Mesh app fails if it exceeds 21 segment message.
However the limit I assume should be at 32 segments and...
Hello,
I'm running nRF Connect SDK v1.9.0 on two nRF52840-DK devices, one Peripheral other Central.
My application requires to initiate pairing, i.e. send pair request...
Hello,
I'm trying to set up nRF Connect for VS Code. I followed this video for installation steps: https://youtu.be/2cv_jjqk5hg, the only difference being that my nRF Connect...
Hi, I'm running the sample "peripheral_uart" on an nRF52dk. It has a config called CONFIG_BT_NUS_UART_RX_WAIT_TIME, which is set to 50. The comment says the unit is milliseconds...
