hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I tryed to reduce the power consumption of my beacon (ble_app_beacone example from SDK) to have more battery live. To do this, I want to reduce the TX power. And also change...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
Hi,
I'm currently using nRF Connect SDK v1.9.0 and developing on a nRF52832 onto a custom board. I'm using a BMI090L from Bosch connected over i2c.
I'm trying to suspend...
Hi.
Encountering an intermittent issue where, after a DFU (either OTA using Nordic Device Manager or over usb serial using dfu-util on Linux), the image is reportedly in...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
In the DTS file for I2C, how do you set the port of the pin specified?
&i2c0 { compatible = "nordic,nrf-twi"; status = "okay"; sda-pin = <26>; scl-pin = <27>; };
In...
Hi,
I have a question about the whitelist，when we use the function "pm_whitelist_set()" to set the whitelist，whether the whitelist is stored in RAM or FLASH? I traced the...
Hello,
I am using nrf52810 with custom board and i have created DFU for uploading a OTA file previously its working fine but i don't know what happens now BLE is getting...
Hi:
When i read data from the device nrf52833 to android app, only get 600byte data and it should be 4096byte. The app use the Android-BLE-Library-2.4.0 lib.
The nrf52833...
Hi,
I have a question on SDK release plans. There is a change awaiting for release (merged after 1.9.1) and it would be nice to develop them with an official release, including...
Hello!
We are two students working on IO-Link Wireless as a bachelor thesis project. Our task is to make a Wireless Master prototype using the nrf52840 DK kit from nordic...
I am making a ble beacon application. I need to send more than 30 bytes of data via advertisement. How can I do? Because UUID data will not be enough for me.
Hello everyone and hello kindly nRF support team!!
One question again sry. I am using SDK 1.9.1 through VS Code and working on the nRF Connect SDK Tutorial - Part 2 -...
