hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hi,
When I try to build a 'light_switch' project on SEGGER embedded studio for nRF connect SDK 1.9.1 for BMD-330-EVAL board. Running into the following error
arm-none...
Hello Everyone,
I am using NRF52833 in my project and I have my NRF module connected to 2 other microcontrollers on UART peripherals. The details are mentioned as below...
We have first worked with a development kit from Nordic (nRF52840 DK) . We flashed the BLE applications using the nRF Command Line Tools.
https://www.nordicsemi.com/Products...
Hello,
I have to open a new discussion session on the same topic because the current session has been closed.
The topic is as follows: devzone.nordicsemi.com/.../at...
Hi,
We currently have a Gazell project that runs on nRF52832 . We have difficulties changing the project target to the nRF52810 .
From the SDK17.0.2, example: "gzll_ack_payload_device_pca10040...
Hi,
I have a firmware (performing DFU over Bluetooth )that runs well on nRF52833 dev kit and for developing the DFU over BLE. I follow this tutorial
https://devzone.nordicsemi...
Using SDK 17.0.2 I wrote a function to modify advertising interval on the run. The function doesn't return any error but the interval isn't changed. What am I doing wrong...
After nrf_drv_twi_tx() function and nrf_drv_twi_rx() function, m_xfer_done is checked using APP_ERROR_CHECK(m_xfer_done). What is the significance of checking m_xfer_done...
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
I download the zip file(nrf-command-line-tools-10.15.4_amd64.zip) in the website.
And then I unzip it get the following structure files:
JLink_Linux_V758b_x86_64.deb JLink_Linux_V758b_x86_64...
Hello everyone!
Long story short, we are developing a BLE application based on the Nordic UART peripheral example. The board (STM32 micro + BL652 BLE module w nrf52832 inside...
Hi All,
I have a question about notify data size.
I have a 10byte array, but the length after Notify is sent will be max len = 50byte which I set in characteristic.
...
6 hours ago
Online steve.hou
2 pts.
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am...
