I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I am developing a react native app with the iOS and Android NRF mesh lbrary. In this app I am handling connection, data receiving on characteristic and sending on...
Hi
I'm evaluating using the nRF52805 for an application that would use BLE but require almost no BLE functionality. Only the ability to periodically wake up and scan is...
Greetings. We are using the zigbee/shell sample in order to verify the connectivity of some other devices running the zigbee stack. While the shell sample had no issues in...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hello,
I want to create a Matter network using my nRF5340 DK board, as Matter accessory, and my RaspberryPI, as controller (CHIP Tool controller). I'm using as well nRF...
Is there a problem with writing-to and notifying-from the same characteristic? Or is it recommended that one create two characteristics, one for receiving data, and the other...
1.SDK:SDK17.1
2.IAR V9.2
3.
static float inv_sqrt(float x) { float xhalf = 0.5f * x; int i = *(int *)&x;
i = 0x5f375a86 - (i >> 1); // this is magic. x = *(float ...
hi ~
peripheral can bond how many smartphones ?
and What will happened if over bond?
i use sdk12.2 below 'is my setting
#define SEC_PARAM_BOND 1 #define SEC_PARAM_MITM...
Hello,
I am developing a door lock system. Where in final product door lock will be controlled and monitored by BLE+Zigbee. So far I have complete success of controlling...
Hi, I'm developing an application using UARTE to reading response from Module Sim. The content response from Module Sim has 495 characters. When I debug, I only read some...
Hi.
I am developing nRF52832 and ST7789.
I'm trying to print out the text, but it's not working properly.
The nrf_gfx_screen_fill() function works fine.
When I proceed...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
