I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi there,
we are a student project and are using the nRF51822 Chip with the MDBT40 module. We designed our own custom PCB and followed the instructions for the circuit as...
I have a subroutine that exercises the SPI interface and only at certain points in the code it won't execute the SPI subroutine and goes into the disassembly when single stepping...
SES IDE, nor nrfConnect programmer tool sees the JLink programmer attached to my PC. No "idcode" in SES. No devices appear in Programmer.
Windows10.
JLink_Windows_V764e_x86_64...
Hello,
I am beginner to work with Nordic, I am trying to setup the development environment for nRF5340 Chipset.
For that install nRF Connect Desktop v3.11.0 version. ...
Hi Team
My SES crashed suddenly. When I tick file->nRF Connect SDK Project, It show below error information. I have try to re-install the NCS from toolchain manager. It...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
To execute the code , first i flashed...
Hi,
Zephyr 3.0 , nrf5340 ncs 1.9.1
i can successfully sent data with
this function ;
So it sends 2 transactions without changing cs state.
1byte tx+rx , and...
Hi,Master:
In BT core_v5.0 2.3.5.6.3 Authentication Stage 1 – Passkey Entry, as shown in the figure below
Question: Why does the process loop 20 times, verifying one bit...
Hi,
I have used the nRF Connect Mobile app to connect a BLE device to my Android device. Once bonded, I can receive temperature signals as expected without issue. I can...
Hi,
I am testing MCUboot in nrf52840 DK
I know that MCUboot can image update using slot 0, slot 1, and scratch area
If so, is it possible to update the softdevice(BLE...
Hello,
We are working on NRF52832 + nRF Connect SDK 1.8.0 for our upcoming product. We need to do OTA of our Firmware.
Could you please help with pointing to the right...
Hi Nordic,
We are using NRF52840 and the NCS sdk to design a new product which may have multiple threads designed. And each thread may need to do some BLE operation at the...
Hi,
I'm developing a peripheral driver which involves UART. I encounter an issue I'm not sure how to proceed.
In my design, I have
main.c
device_drv.c
device_drv...
