Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, we have a thread that essentially is running a loop and we want that thread to be running for all the lifecycle of the app. If for whatever reason that thread died...
Hi Team,
I am using Open Thread networking protocols in my projects to communicate with the devices .I have seen while trying to changed some parameters over the network...
I am unable to do a FOTA with the SLM application on a nRF9160. When I try to do a FOTA with the command below, I get a 404 even though I know the URL exists (real host name...
Hello,
I have been working with custom nrf52832 board to develop firmware for my product. I have been trying to compile the example secure bootloader from the SDK v15.3...
Hello, I am developing a uart communication between the nrf52833 and the nrf9160. I found some examples but I don't want to use the HCI layer, I prefer to use the NUS service...
We have an application that wakes-up every N minutes and listen to devices in a ble mesh then performs many other actions. In order to save battery, we would like to power...
Hello
OS :- Linux
Hardware version :- BC805M
SW :- Segger embeded studio
I am using nrf52805. I am test it with ble_app_uart. It advertisement continuously and shown...
Hello,
I'm trying to transfer data to an L2CAP CoC on a nRF52832 from iOS and Android devices. I've configured the MTU and MPS so that the SDU fits in a single packet with...
I'm using BLE Mesh Sensor example that Client & Sever communication data each other.
Because I'm implementing one by one communication data that client > sever > client...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to add a custom UUID in the advertisement packet and scan for the custom UUID in the central device to...
Hi,
Our firmware currently only support full modem update, and I would like to perform a full modem firmware update from 1.2.0 to 1.2.7. According to the reply from https...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
I am getting a softdevice hard fault occasionally, on fully enclosed devices with no debugger port access.
Where can I find info on potential causes of this fault?
nrf51822...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
