Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Is an adaptation of https://github.com/microsoft/Windows-driver-samples/tree/main/bluetooth/serialhcibus for the Nordic / Zephyr hci_uart sample available?
Like https:/...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk. I use peripheral_uart sample.
I follow the guide:
https://devzone.nordicsemi.com/guides...
Hello,
I have made a lot of work with nrf52840 microcontroller and i am in pre-production stage.
NRF Connect is not loading in vs code.
I have tried to uninstall/reinstall...
Hey,
I am using an HID keyboard + keyboard toggle in my project,
When the nrf connects an iOS phone, it takes control over the phone's keyboard.
To release the kb we...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
I am trying to get a PWM waveform output at 50% duty cycle with 409.6kHz frequency based on...
Hi,
I have a NRF52840 USB dongle( https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle); is Any possible to flash NRF52840 dongle with PTS Firmware Upgrade...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
Hello,
The following is for a custom application but I have also tested this with the base peripheral_uart example with the same result.
I have an application which uses...
NRF52820
PAN1781 EV Board
Segger Embedded Studio 5.62
nRF5_SDK_17.1.0_ddde560
S140
Hello,
I'm currently working on an indoor positioning system and as the title...
Hi,
I compiled an application that should start at address 0x40000. However, executing an OTA DFU always places the application at 0x26000, right after the softdevice. ...
In a previous ticket on another topic this question came up. Given it was a tangent to the original topic of that thread, and I think it would be helpful to others, I decided...
OS: Ununtu 20.3 LTS - Kernel: 5.4.0-109-generic
Software: Power Profiler launched through nRF Connect for Desktop v3.11.0
Hardware: Power Profiler Kit II
Problem: Cannot...
