Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi
I am working with an nRF52DK board that is successfully communicating with Nordic's nRF Toolbox app via BLE UART.
I would like to be able to modify the app as I modify...
We need to read/write to an I2C device that uses a 16-bit register addresses (Melexis MLX90632), and the nrf_drv_twi_tx() and nrf_drv_twi_rf() functions seem to be limited...
Hi,
We would like to impelement Pairing and security features in our device. Our device will act as server in peripheral mode. The cleint device should ask for 1 passkey...
Hi Nordic,
I'm referring to this doc but still not quite clear about how to enable the chip for BLE RF HW validation.
infocenter.nordicsemi.com/index.jsp
What would...
Hi,
I have modify the payload of the Light Switch example of the NRF MESH SDK. When I send 50 bytes or less, all works fines : the server nodes received all the bytes...
Hi everyone,
I am developping on a custom board using nRF52840, using MCUboot v1.8.99-ncs1 and nRF Connect sdk v1.8.
For development matters, I would like to change the...
Hi, I want to include the pairing and bonding features in my application.
I want to use the LE secure connection method. For both initiator and responded the IO capabilities...
I adding custom pins declarations through overlay file as in first image with corresponding yaml file ( see attachment) with path .. /dts/bindings/gpio/custom.yaml. The project...
Good Day. I am wondering if anyone could maybe assist me in where I am going wrong with my software.
I have the intention of using a Nrf9160 as a serial modem through AT...
I use nrf9160 to develop a product for customers. The modem is also set to PSM and the log is turned off. However, I find that when the modem is connected to the Internet...
When I try to connect to nrf52840 using J-Link, the following error is detected.
What is the reason for this "Failed to power up DAP"?
- Connecting via USB to probe/ programmer...
Hello Devzone,
I am building firmware for an nRF9160 based device, starting with an ncs 1.6.1 sample app and LTE modem firmware v1.3.1. I'm in North America, and when testing...
We are in the process of the developing a wearable product and we have already developed a series of prototypes, in which one of the components is the nPM1100 but we have...
