Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi there,
A couple of weeks ago, I'm facing the issue that my nRF52840DK board is not visible and led5 is flashing rapidly. I reflashed the bootloader, j-link-ob-sam3u128...
I added some functionality to asset_tracker_v2. I used two pins of Nordic chip for following purpose: 1. Detect BMS, pin as Input 2. Reset BMS, pin as output. The pins overlay...
Hi,
I'm a newbie of microwave board design, after many research I finished our 2.4G USB Receiver board which use the nRF52840-QIAA. But I still want some advice of the RF...
Hello,
My setup is UDP sample and PPK2 for power measurements. I am trying to figure out the best settings that are available with eDRX set to <= 20.48s, and preferably...
Hello,
I am trying to get the data out of an out of the box zigbee sensor (PIR motion sensor) with the CLI example provided.
I flash an NRF52 with the CLI example, and...
We are working with tuning of the GPS:
Basically the tuning is fine but we are mostly bandwidth limited.
I wanted to ask how much is the acceptable bandwidth for a GPS...
Hi Team,
I am working on air mouse development using NRF 52832.
nrf standard package support ICM 20608 with AIR_Motion Library , but its not available now in https://www...
Hi,
I have noticed that when a peripheral (using NUS) is disconnected from a central it takes 2-3 seconds for the peripheral's BLE_GAP_EVT_DISCONNECTED to trigger.
Shouldn...
Hi,
I encountered that the PWM couldn't be closed completely, it still has about 100uA after PWM is uninitialized.
For troubleshooting purposes, I have posted my code...
I am working with SPIS on nRF5340. Since my RX and TX buffers will not change, is it possible to call nrfx_spis_buffers_set only once, during initialization? I tried to do...
I am creating the Battery characteristic in a Battery service but I run out of memory (0x04 error) when generating the characteristic. However, that makes no sense. I have...
We’re using Nordic Semiconductor nRF52840 and we may have some problem with RTC when we simulate a brownout. In our application we have both coin cell battery and external...
when I am trying to setup linux with this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/gs_installing.html#install-the-toolchain
On typing this command...
