Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I am debugging an Application running on a custom board that uses the NORDIC nrf52832 processor connected to an IMU over twi. I am using SDK17.0.2
I find WDT is kicking...
Hello Nordic Team,
I've been having good success with the 52840 and been slowly migrating a lot of my projects to the chip. While I await modules to arrive from a supplier...
I'm trying to use 9-bit UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_DATA_BITS_8...
Hello,
NCS1.9.1, nRF52840DK, Windows10 X64, VS Code,
1.
i want to read voltage from RT_ADC pin (P0.04),
and than converting NTC thermistor value to Temperature.
...
Hi,
My setup include a nRF52840-DK board that has an ESP32 WiFi module connected to it via UART. The idea is to source the new firmware from a server located in the cloud...
Hi, I'm doing experiments with Bluetooth direction finding. I am using the example of the nRF52833 development board, and I have obtained the IQ representation of CTE and...
Hi I am using the aws_iot example on the nrf9160 DK.
I have opened the zephyr.dts file and in the section uart0: it has the following
I've reached this point trying...
Hi,
I am looking to connect the ds18b20 sensor to the nrf9160dk. I followed this post, but when I tried running it, I was getting a "create_nordic_project.py failed (1)...
2022-04-12
Hello Devzone Community,
I have a couple questions regarding availability of nRF9160 LTE modem settings PSM and eDRX. Question (1) If my local celular carrier...
Hi Nordic Support,
I'm running into an issue with ncs v1.8.0 directing log and shell to RTT backend.
Objective: Using nRF NCS / nRF52840dk - I want to dedicate 1x UART...
Hi,
I have opened a ticket with Kenneth and verified it by mistake. It is now locked. I have done the changes Kenneth asked me but it didn't resolve my problem.
thanks...
Hi,
I am connecting my nrf9160 based system to the nRF Cloud and sending data from it.
I got the cloud to show the RSRP values that I sent it through the following JSON...
NCS 1.8.0
Modem FW 1.3.1
For other products I've worked on with cellular modems, we would add in back-offs to the firmware in the case we failed to open a PPP session...
