I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi there,
We are currently doing some testing around the low power modes of the nrf5340. Detailed info on the Low Power mode and Constant Latency mode is a bit hard to find...
Hey,
I'm trying to follow a few guides on sniffing BLE connections (eg https://hackaday.com/2021/03/23/a-crash-course-on-sniffing-bluetooth-low-energy/ ) with an NRF52...
I'm trying to get my nrf9160dk board up and running with the nrfcloud service. However, when I input the SIM ICCID and PUK, the nrfcloud site starts it's "working" process...
Good day
After flashing a sample to my thingy 91 I seem to have lost the Jlink connection. All im picking up is the UART via nRF connect Programmer. Is there a Bin file...
Hello Sir/Mam;
I am new in nordic environment so i need your valuable guidance . i want to read a sensor data using Uart . I have successfully do same thing on Arduino board...
Hi,
I had previously asked about SPI interfacing of the RFID card reader and I was successful in creating a custom application using connect SDK 1.5.1.
But according to...
I currently have an application with B0->SPM->MCUBOOT->APP and am looking for an example of how to upgrade MCUBOOT itself over the air from a file downloaded from some server...
We're using a nRF52DK and the Nordic-Programmer-App to flash our firmware on our custom boards. After upgrading to Programmer v2.3.3 I'm getting the Error-Message "Part of...
Hi,
I am able to successfully build and flash applications from the CLI.
When setting up the nRF Connect VS Code extension, I run into an issue where it can't seem to...
Hello, I am trying to use the spi_flash sample project with a laird bl654 dvk. When I run the project however, dev->state->init_res = 19 and will not run for me. It recognizes...
Hi,
I have been trying for several days to modify the ble_app_uart project on the peripheral side to use the BLE Long Range, unsuccessfully. I use the NRF52833-DK with...
Hello, sir.
I want to use the i2c bit bagging method, thus I used the DeviceDownloadnRF5 SDK 17.1.0 ddde560nRF5 SDK 17.1.0 ddde560componentsdrivers nRF5 SDK 17.1.0 ddde560componentsdrivers...
I want to use the Zephyr Shell with my own transport layer. Since the only connection I will have to the modem is over SPI, I want to have the SPI read/writes handled with...
I am using sdk 17.1.0 .I am getting error while using bsp_buttons_is_pressed function in main although i have included file bsp.h ,bsp_btn_ble.h, boards.h. The error is Error...
