I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
In SDK 1.9.0 i saw that QSPI deep power down was implemented and i can confirm that that works using the below code. The issue I see is that if the device is in deep power...
Hi,
Is there any sample/example that comes with SDK that shows how to add extended data in BLE advertisement (using Zephyr)?
I have tried adding some additional bytes...
We have 3 nRF52840 to establish a net. one for master device, One for Master device, One for HUB(Msater-Slave) device, and One for Slave device. The data flow is Slave device...
Hi,
Following the update of my mac (M1) in Monterey, i can no longer flash programs on my board (everything worked under Big Sur).
I got the error JLinkARM DLL load...
Hello,
I am currently trying to add a FEM (nRF21540) to an already existing BLE project that is using nRF5 SDK. For that purpose I ordered the nRF21540 DK that is using...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now my customer ask me if it possible to have the LQI value...
Hi,
My goal is to use a timer to trigger SPI transactions and the spi_event_handler() to trigger bluetooth transfers. In order to make it as fast as possible, I would...
Hello, we're trying to make products using BLE with nRF52840(central) and nRF52833(peripheral).
We did make custom boards and also made a program that once paired(bonded...
Hi all,
I'm working with a pressure sensor (LPS22HBTR) and the nRF52-DK and I have some issues when sending data through BLE (nRF52832). When I run the program without...
I have recently upgraded from NCS 1.5.0 to 1.8.0 and noticed that the native TLS stack (vanilla mbedtls) was no longer being used for TLS based sessions.
My use case requires...
Hi,
I found the online power profiler for BLE ( Online Power Profiler for Bluetooth LE - opp - Online Power Profiler - Nordic DevZone (nordicsemi.com) ), it helped me to...
I was working with VS code just fine and then upon booting it up today suddenly nothing will build anymore including sample projects. the only thing that i could tell that...
hello Nordic
i am working with nrf52840, with zephyr 2.6.9, ncs 1.7.1
i want to have an interrupt on a pin toggle and have a callback for up and one for down
i configure...
