I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Dear Nordic team,
For the security reason to be safe from the hacking, we like to completely disable the debugging and flashing port during production.
Would you please...
In nRF21540, two antenna ports are for antenna diversity. These two antennas are placed on the receiver side or one of them will act as transmitter and other as receiver?
Dear,
I followed the ticket below to set peripheral_lbs for nRF5340.
but still cannot see the 8uA in power consumption.Would you help?
I also use nRF5340DK and multi...
Board: nRF5340-DK
Version: NRF5340_xxAA_ENGD
SDK: 1.5.1, 1.6.1, etc
I have a Bluetooth project that also has quite a high SPI bandwidth requirement, so hence I am...
Hello Guys,
I am facing an issue with nrf52840 usb dongle.
I am using an external debugger J-Link for debugging the target ic.
During development, i have succesfully...
I am integrating flash storage example ( nRF5_SDK_17.0.2_d674dde\examples\peripheral\flash_fstorage) in ble_app_hrs_rscs_relay (nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral...
I am trying to implement bonded pairing with a project in which I already have NVS configured for user data. When implementing bonding, I understand that I need to remove...
The term advDelay is being used for the 0-10 ms random delay added to the fixed advertising interval. Since it is set by the link layer and can't be controlled by us, I want...
Hello,
I'm evaluating power optimization on nRF52. I'm using a Power Profiler Kit II and a nRF52-DK board.
I tried a lot of configuration and everything work as expected...
- The product I am making uses nRF52833. In addition, the audio part of Thingy 52 was added to the product as above. (The speaker uses 1.5W, 8ohm. Current consumption is about...
Hello,
I am trying to learn bluetooth using nrf52840 USB dongle. I have created an application from sample beacon and i would like to use I2C to implement my own driver...
unable to use time.h file
i have used:
#include time.h in main.c
added time.h file from C:\Keil_v5\ARM\ARMCC\include\time.h
when i use
time_t T = time(NULL); srand...
I have recently upgraded my working stack based on nrf sdk for thread and zigbee v2.0.0 to nrf sdk for thread and zigbee v4.0.0
But since then my mtd's are not getting commissioned...
We have built our application in nRF SDK for Thread and Zigbee. Since nRF SDK for Thread and Zigbee is in maintenance mode now, we plan to move our application to nRF Connect...
Hi,
I had my application based on nRF_SDK_For_Thread_and_Zigbee, and now I am porting my application to nRF_Connect_SDK.
When I use the nRF52840 DK board for testing...
