I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I have two custom images that I flash to my chip (nRF52832, SDK v16.0.0, SEGGER Embedded Studio). Application 1 is located at 0x26000 Application 2 is located at 0x45000....
I am new to embedded f/w development. I would like to be able to debug zephyr projects. Can anyone recommend a debug probe to use with the nRF5340? and any debugger software...
Are there any other SDK options for nRF5340 than nRF Connect SDK (and Zephyr)?
The chip would be nice, hardware-wise, to a project, but the nRF Connect SDK looks like a...
I am having a similar issue to the person in this post where the wake from deep sleep on an interrupt sometimes works and sometimes doesn't. But for me, it's very consistent...
Hello,
I know this question has been asked a lot. But I haven't found one that matches exactly. I'm trying to flash a custom PCB with an nrf52832. I'm using the on board...
Hi,
I am trying to get a simple LED blinking using a timer, gpiote and the ppi. So the Idea is:
Timer compare event -- PPI --> gpio toggle. I am using the nRF connect...
HI,
I am developing an application which requires BLE connection. I am concerned about the energy consumed by the device during the connection.
I understand that once...
Hello,
I'm just starting to use Asset Tracker V2 from v1.9.1 and it appears that it is missing some device info such as version, carrier and other on the Device Information...
Can I use SVC function in my application code to copy bootloader image into flash instead of using mbr commands? If this is not possible, what are the other alternative options...
Hello,
I'm trying to send a custom reliable message between two nRF52840 DKs, using the nRF5 SDK for Mesh v5.0.0 and nRF5 SDK 17.1.0, by modifying the light_switch examples...
Up to now I referred to the name of the tag from the west manifest to know the zephyr release. So I assumed that the v2.7.99-ncs1-1 tag was from the zephyr 2.7 branch until...
After executing nrf_libuarte_drv_rx_stop(), nrf_libuarte_drv_rx_start() will produce an error.
In nrf_libuarte_drv_rx_start() t his line in nrf_libuarte_drv.c (Line 625...
Hi ,
i am working on nRF52833dk board. here am running sample example from sdk. i.e. peripheral_lbs example. my query is whatever the Bluetooth api it is calling inside...
