Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Morning Everyone,
We use raspberry pis as part of our test equipment. The final stage of our CI/CD pipeline downloads the build dfu packages to a Pi and then does an OTA...
Hi,
I try to run SDK17.1 examples/dfu/secure_bootloader/pca10040_uart_debug.
Only UART example does not have softdevice.
I build and run that example on SES on M1...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Hi Sir/Miss,
I encounter a problem which is in programmer software.
When I open software and connect to nRF52840 DK. Right flash size window will display some animation...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Hi there,
I'm currently using SDK 17.1.0 with the NRF52832 Development Board. This is pretty new to me, but the examples helped me get an application going pretty quickly...
I'm using a nrf52840dongle board with the prj_no_dfu.conf configuration with the following additions:
CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n CONFIG_CHIP_LIB_SHELL=y CONFIG_LOG...
Dear Nordic Engineers
I install nrf command line 10.1.6.0 in my office PC.There was a problem after the installation complate.
I input "nrfjprog" in powerShell ,it's normal...
Hello,
we have a remote control with 7 buttons.
Every button shall wakeup the device from deep sleep.
Beside i will have an interrupt on Button 6 and 7.
So the problem...
I am using nrfconnect 1.5.1 (zephyr/command line) with modem firmware 1.2.3 and believe I have found a fairly serious bug/behavior in the UDP API. It is pretty easy "crash...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
In the nRF5340 product specification version 1.2, I see an internal bandgap reference error range of -1.8/+0.5%.
In the nRF5340 product specification version 1.2, I see...
