I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
I have followed Einar's response on the below thread but I still cannot see the logs on the SES
https://devzone.nordicsemi.com/f/nordic-q-a/79682/adding-mcuboot-bootloader...
Hey devs,
I'm trying to get the i2c interface to work with the MP8862. I followed the TWIS driver guide to get started and in there everything worked.
Now I wanted to...
Hi Everyone,
I'm using VS Code, nrfConnect SDK v1.7.0
I'm trying for minimal bluetooth roles(either central/peripheral) along dfu support in nrf52820 chipset.
when I...
Hello,
I recognized a wrong answer is sent by the ZigBee stack of nRF Connect 1.5.1 and 1.7.0 (and others).
Eg. the application provides a color control cluster as a...
Hello.
It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am implementing the advertisement processing, but the advertisement stops when...
Hello,
I compiled pc-ble-driver from github and it when i debug heart_rate_collector in adv_report_parse function i only get 1, 10, 255 field_type and never BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME...
Hi,
I am trying to erase and flash a nRF52840 chip on a custom board. I use a J-Link EDUwith the Cortex M adapter to plug onto the board. I checked the hardware conf several...
I am using libuartes example. I only use send_UART (char*sdata, int len) in main before while (true) or in void uart_event_handler(void *context, nrf_libuarte_async_evt_t...
I'd like to use Power Profiler to measure really low currents (watches) ~0.4 microAmps.
However, Power Profiler II measures 1.5microAmps even when disconnected with or without...
Hello,
Have anyone knowledge on how to force to include, using nRFSDK, the AdvA field in the Ext Hdr of a BT 5 long range advertisement primary packet frame ?
We are testing...
