I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I am developing Coap-Client and Coap-Server devices using nRf52840 dev kit. I am using ncs 1.7.1 sdk. I have a few questions.
1- I can successfully send a data received...
Hello all,
I have recently developed a custom board that uses an nrf52810. It also contains an accelerometer as well as some hardware for regulating the voltage and charging...
hi
I am using nRF5 Calendar example and
I have this problem
could you help me, how can I fix that?
I don't use the UART functions, I'm going to use SSD1306 to...
Hello!
I am currently working with Actinius' Icarus IoT board and I'm trying to get the interrupts to work. This is the boards' pin layout: At the moment I have connected...
Hi everyone,
I am trying to create a system to collect data from different sensors and store them in a FRAM. Then by using SPI, I want to transfer the data to the nRF52832...
Hi,
Trying to build the asset_tracker_v2 application I finally get the following error:
Rebuilding ‘zephyr / zephyr.elf’ from solution ‘build’ in configuration ‘Common...
Hi All,
I have problem running nRF5340 in continuous mode without any external trigger (timer/ppi). I would like to setup SAADC so that last conversion triggered new set...
Hello there, can I use the JTAG interface of the nrf52840 to perform a boundary scan of the components connected to it? I'd like to have fewer testpoints in my pcb and use...
I want to use CONFIG_UART_0_NRF_UART instead of CONFIG_UART_0_NRF_UARTE. But I don't get any option for this because CONFIG_UART_0_NRF_UARTE is selected by default .
I...
Hello everyone,
I am working on a project based on nRF Connect SDK v1.7.1 that I want to move to the new SDK v1.8.0. But I'm experiencing problems when building the project...
Hi We'll be adding to a design that uses libuarte/UART0. I've tested/run the example code and it's fine. Changing/swapping index from UARTE0 or 1 works fine as does reassigning...
Hi Sir/Miss,
I use SDK 17.0.2 version and softdevice s112 7.2.0 version to develop in nrf52810.
And, I base on this project (NUS with static passkey) which imports CTS_C...
Hi everyone, I'm developing a program with the NCS 1.8 using NRF52840 and I want to use the SPI, the fact is that I've to connect my device to those pins
And as you can...
