Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
Working on a zephyr/zigbee/802.15.4 system and my code (loosely based on the Nordic samples) on a custom device was not behaving as expected.
So I broke out an nRF5340 DK...
Hello Devzone,
I'm writing to ask about how long a device running Nordic's aws_iot sample app (sdk-nrf 1.6.1 based, Zephyr 2.6.0 based) may be in a "radio idle" state, and...
I'm using an application based on the MQTT_CLIENT example. Without any change, it worked fine.
Now I tried to add UART2 as a communication channel to another controller...
Hi Community,
I am using ble_hrs_heart_rate_measurement_send API to send notifications to my central device which is a android mobile.
Recently I have observed packet...
Hi,
I am writing an app for nRF52840 with sdk 17.0.2 and freeRTOS.
The device should be a peripheral which a android app should be able to connect to.
Everthing works...
Hi,
How are you?
Could help someone with a ask?
I am designing a plate and I am using like guia the nRF9160 DK. The Layer Stack Manager has configured the Top Layer...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi Nordic Team,
My dev enviroment is as follow:
nRF52832(ble central)+ S132+ SES+ SDK 17.0
We are facing an issue regarding local BLE Address . When we are flashing...
Hello.
I am developing a peripheral roll using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to know the information of the device that sent the connection request. Also...
