Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
I'm testing with the new rev of the nRF52832 (build code QFAAGB on the package), and I'm not able to observe behavior that makes sense to me per the updated product spec....
Currently working on a nrf52dk_nrf52832 kit. I have a SPI flash that I am trying to use - I am using the nrf SDK ncs v1.9.1.
I know I can use any of the GPIO pins for SPI...
Hello
I have a mesh node that needs to broadcast a custom BLE packet
To start advertising I call bt_le_adv_start and it works as expected.
I'm curious about the error...
I've been trying to enable the watchdog as early as possible during boot. I haven't been able to find any way to configure the nrf52832 watchdog to enable itself prior to...
Hello,
I'm in nRF Connect SDK 1.5 and I have to change the baudrate of UART1 at runtime. I have to use Zephyr UART Functions. I have tried the function uart_configure()...
I have a customer that has been using the nRF Connect Mobile app on his iPhone to test his device and its works perfectly and he can do all the functionality he wants including...
Hi.
I am developing using nRF52832 & ST7789 round LCD.(softdevice : s112, SDK version : nRF5_SDK_17.0.0)
Currently, I am trying to develop using the gfx library, but there...
I'm comparing some of the ZBOSS API between what's in the nRF5 SDK for Zigbee and what's in the nRF Connect SDK, and I'm curious about the differences in some cluster list...
