Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am developing on an nRF52811 and I've noticed that I can't set/clear the pins such as the ones in the bracket in the picture below.
I'm using nrf_gpio_cfg_output(pin_num...
My product is devloping in nrf52810 with Zephyr . The flash is too small. At present, using all peripherals, the size of app_update.bin is 55KB. The size of MCUBoot partition...
Hi,
I'm a beginner, I want to do a test that will create a thread by "K_THREAD_DEFINE" marco.
Then I will continuous print "Hello~~~" per second. That's all.
But I don...
Hi everyone.
I'm approacing to the nrf52833 SoC following this official tutorial but when I import the example template the VSCode finds the cmake tool in my espressif ...
Hello,
SDK Version - 17.0.2
Mesh Version - 5.0.0
I'm using nRF52840 DK to build mesh example(light_lc_server & scene_client).
I try to save the scene of the...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 I have two quick questions. 1) How to add version information(string) when make binary. 2) How can I read version when I finish...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
