Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi
I need to read the Drive mode of how an output pin has been configured....
I see that there is an API to read pin's Pullup, Direction, Sense, etc configuration.....
Hi,
I want to make an emitter and a receiver for AOA. I have seen that the example i have to use is " Direction_finding_connectionless_tx (and rx)" but when i open it on...
Hi,
I'm using two UARTs on nRF52840 with SDK17.1.
My issue is both UART works individually until they receive messages at the same time. Both of them receive an RX overrun...
Hello,
NCS1.9.1, VSCode, peripheral_lbs
nRF5340-DK got error:
undefined reference to `z_impl_k_busy_wait'
nRF21540-DK and nRF51840-DK work well.
Best re...
Hi,
I was measuring the time it takes to boot to my application based on the nRF52832 and the time I measured was excessively long.
I'm using a PicoScope DSO for observing...
Hi,
I've been requested a feature regarding buttonless OTA DFU that I'm not sure if it's feasible or advisable to implement.
The feature is that once the OTA is successful...
Hi,
I do not know how to reliably get size of arbitrary UDP data received by #XRECV or #XRECVFROM.
It is clear for text data, but for binary data both #XRECV and #XRECVFROM...
Hi everyone,
I have a preblem for BLE Mesh 5.0 version (board is nrf52840),
I found that in the Setting set function of the Sensor Model, it seems that the data is transmitted...
Hi, I am using Zephyr and want to use the nrfx_timer_compare functions. It seems that the system is working with Timer4 and channel 0 to 4. However, the compare of channel...
Hello,
I have many board of nrf9e5 IC's,
But in nordic company it's discontinue,
It had long range and easy to set,
Now which product is like this?
I need part number...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Hi
I have combined the ble_app_uart and libuarte example. The combination works "nearly" well.Transmit is ok, but when receiving characters over UARTE, no NRF_LIBUARTE_ASYNC_EVT_RX_DATA...
I see a square hollowed out area in the middle of the newly released questions about nrf5340 audio DK PCBA. What is the design purpose of this hole hollowed out area?
