I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
I've just received nRF52840, it powers up and blinks as programmed and the buttons work. I hear the "ba bing" on my PC when it connects and disconnects, but the JTAG does...
Hi DevZone,
I need to change some defines in the ffconf.h file used by nRF5 SDK to set configurations for FatFS to enable use of f_findnext(), f_findfirst(), etc.
Is it...
Hi,
I have provisioned some nodes using interactive_pyaci successfully. Functionality is as expected. As a test, I then shut interactive_pyaci down, rebooted the nRF module...
Our Gateway uses a NRF52 and the sensors a NRF51.
Gateway is outside the freezer at + 20C and the sensor is inside the freezer at -30C.
What we see is the pairing becomes...
I'm working on a wireless musical instrument which requires a super low latency RF link. I previously was using NRF52810 and found that the latency was too high. The complexity...
Hello,
I'm a beginner ... I would like to connect a LoRa module (REYAX RYLR896) to send data from my nRF52840 Express to an Arduino UNO (with LoRa).
I don't know how...
Hello,
I am trying to work with the DFU examples provided with the SDK. My board is a custom USB dongle to which I need to add the bootloader. Following the steps from...
Is there a way to enable LE privacy for nRF52 DK in Bluetooth Low Energy App of nRF Connect for Desktop? I would like nRF52 DK to use resolvable private address when connecting...
hi, Im trying to read from a sensor register using TWIM peripheral on nrf52840 in blocking mode, but it wont work , doesnt freeze or anything .. just doesnt work
below you...
Hello,
I am trying to set system on mode in nrf52840 usb dongle.
This mode switched automatically by idle task, when there is no thread running.
There is no while(1...
Hello,
I m new to nordic in VS code. Bought two nRF5340 DK for ADC conversion and wireles data transfer.
Followed all Youtube install instructions "nRF Connect for VS...
Is it possible to communicate with the of nRF52840 through USB, for example using PyUSB?
If yes, is there any documentation that can help in this regard, e.g. documentation...
These are Central device 52840 settings:
These are peripheral device 52810 settings:
I use official sdk16.0. Central Project is ble_app_multilink_central...
HI,
I am designing a costume PCB of nRF52840-CKAA-R7. I used Johanson 2450AT07A0100 Chip antenna for BLE, please suggest the matching circuit for it.
Due to size concerns...
