Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hi Nordic，
I am using nrf52840 custom board. May I ask, can I replace 4.7uf near VDDH and VBUS pins to a larger cap, like 10uF? As far as I can see, these caps are only...
I installed the nRF Connect extension pack which also contains the nRF Terminal extension but I cannot make it work in VS Code
In the command pallette I select nRF Terminal...
I wrote some code to read the Adafruit PDM Microphone Breakout board sensor output (ST MP34DT01-M microphone) with Zephyr and nRF Connect SDK into the Thingy 91.
I do this...
Hello
Im trying to use my iPhone 13 with your application nRF Connect as a peripheral.
For some reason the moment I make a connection with another device it automatically...
Hello,
I am using the Adafruit Feather nRF52 Bluefruit LE - nRF52832 for a project where I will have to transmit and receive data over Bluetooth Low Energy between two of...
Hi,
I have a nrf5340 SPIS peripheral being driven by an STM32H753 micro. Data transfer works fine except when I connect a scope probe to the CSN pin. With the scope probe...
Hi,
I have been trying to chase down an issue with the flash manager occasionally raising an assertion in mesh_config_backend_init() after a power cycle of the nRF52840...
Hi everyone,
I have this problem with the firmware protection method in nRF52833. As far as I know, when using secure boot-loader, it can prevent other programmers to flash...
Hi everybody,
I want to modify the Tx characteristic on Nus service to Indicate.
Keeping if is possible Rx characteristic as notification.
Are there some tutorial or...
Hello, support
I use nRF52833 SoC and need to host it with external NXP MCU to control its function, interface is 3 pins only, I wonder whether there is any example code...
Hi all,
I'm trying to debug my nrf52480 with vs code.
I followed the nRF Connect for VS Code tutorials: Add an existing application, add build configuration and than...
Hi Guys,
I want to have some BT-SIG RF PHY tests on nRF5340 DK with R&S CMW270.
I can perform direct test mode in nRF Connect for Desktop,
but I cannot connect nRF5340...
Hi, I am developing my own application based on the newest demo direction _finding_connectionless_tx and direction_finding_connectionless_rx with Dev board nrf52833.
I am...
Dear Nordic Engineers
I used NRF CONNECT SDK on NRF52840,I have some questions,Please help me.
1、I used the buttons module of the Common Application Framework ,but I found...
Hi Nordic:
We are working on a project, using NRF52832, which has the functions of softdevice+bootloader+ble+dfu, the SDK we use is version 17.0.0,
and RTC2 is used as...
