Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Dear All.
I tried to test and evaluate LoRaWAN stack on Zephyr, without success. I will need more time to debug what is happening by the logic analyzer. Meantime I attached...
Hi,
I have enabled SPIM on nRF52810 and worked normally.But when I enabled on nRF52832, it worked unusual.
I had defined CONFIG_NFCT_PINS_AS_GPIOS because used P0.9 and...
Hello,
We are using lwm2m client project SDK version v1.9.0. We need to enable #define CONNMON_LAC 12 to get LAC value but i am facing problem to enable #if defined(CONFIG_LWM2M_CONNMON_OBJECT_VERSION_1_2...
Hi,
When I download the example of "ble_app_uart"(SDK17.0.2 S132) in nRF52832,mty board is working as normal. But when I add RNG in main, the RTT Viewer just logging SOFTDEVICE...
I have some odd cases where an nrf53 based device just disappears from BLE. It's no longer connected, and not advertising.
I'm looking for a method for the application processor...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. A port is connected to the board to communicate...
Included "bsp.h" and "nrf_fstorage.h" still getting these below errors:
undefined refence to `bsp_indication_set'
undefined reference to `nrf_fstorage_init'
undefined...
Hi,
I use the nrf mesh sdk for long time and I just see that its migrate to zephyr rtos.
After reading the nrf mesh sdk doc and the zephyr project doc, I have some questions...
Good afternoon.
We're using nrf Connect for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and its associated...
0 dBm TX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 7.1 mA
Radio RX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 6.5 mA
I want to know which example is tested...
The CAN controller MCP2515 should be connected to the Nordic DK NRF5340 by the SPI interface.
Communicate to Arduino uno
We were trying with CAN sample given
But this...
Hello,
I've tried to request the location via AGPS/PGPS via Location sample in SDK 1.8 but it seems that location is only working with the Cellular method.
I've tried...
Hello there, I am new to your product, and I am trying to understand your library logic and hierarchy. Right now I am trying to figure out what all of these prefix (such as...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
