At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
Hello there,
I am using the rtc2 in NRF52832 to interrupt at randomly generated time instances. Now, I am trying to integrate this functionality in a framework that uses...
I would like to use the low power pwm library to get a breathing LED effect on my device. The MCU I am using is a BMD 350 and the LED is connected to nRF52 port P0.02.
...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
Hello!
I am trying to install MCUMgr on MACos.
I install the Go Programming Language and then follow this: https://docs.zephyrproject.org/latest/services/device_mgmt/mcumgr...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
Hello, I would like to make a follower robot. For this, I wanted to use the AoA to locate my phone and thus determine the direction in which the robot should go.
I'm really...
Hello,
I am working with a nRF5340 and need to use both CDC and mass storage on SD Card. I started my application based on the CDC example and it has worked fine.
Now...
Hello,
NCS1.9.1, VSCode, nRF52840,
from link UART Driver – Nordic Developer Academy (nordicsemi.com)
uart can't to receive data continuously,
receiving evt->data.rx...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
