At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
I have a battery with 4.2v max charge. Since this is outside the input range for nrf52832, I have to add a down voltage regulator. Now the question is: Should I...
Hi!
I need to modify the code of the secure and the non-secure images of my project.
I tried to follow this guide https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
Hi
I have a project which is using 53832 as the master , main 52832 works with smart phone by bluetooth ,and broadcasts ebike information throght the ANT+ .
I would...
Hello everyone
I have a bunch of custom dongles from the company I work for and two of them started to behave in a strange way after I tried to erase and program them through...
Hi,
I'm currently in the evaluation phase of a project and would like to use a NRF52 chip, but I need to ensure, that I can use two independet hardware timers. I had already...
I am running a PWM pin on 15 using this DT Overlay:
pwmnmos {
compatible = "pwm-leds" ;
status = "okay" ;
pwm_nmos0: pwm_nmos_0 {
pwms = <& pwm2 15 >;
};
...
Hello,
I built my application based on your "ble_peripheral_lbs_coex" example. Board is nRF5340DK.
Mesh and BLE (NUS service) run together but I noticed that the NUS UUID...
I'm using SDK 17.1.0, softdevice 7.2.0 as a Bluetooth peripheral. I'm sending notifications to a paired iPhone. The notifications are keyboard keys, and so are time sensitive...
Hello,
I am trying to figure out how to save a small number of counters to local non-volatile memory on the nRF9160. I have a few questions.
1) How do I determine whether...
Hi
I want to measure chip temperature of nrf52840.
For this I referred " sdk-zephyr / samples / bluetooth / peripheral_ht / src /hts.c"
and I have enabled "CONFIG_TEMP_NRF5...
We are using nRF9160 DK (SDK 1.9.1) with "serial lte modem" firmware. We are trying to test downloading files from a server using AT commands to work with HTTP. The file is...
Upto a week I had *no* problem in programming a nRF52840 dongle with an app I am porting from the nRF52840dk.
All of a sudden I can't get the app running, the dongle appears...
I'm trying to get sprintf working with SDK 17.1. Basically, I'm struggling getting this simply use-case to work. char buf[32]; sprintf(buf, "%.3f", 3,5); I'm not able to find...
I know from zephyr samples that Tensorflow lite is available via zephyr as an external module, though it's not explicitly allowed in the nrf west.yml, and therefore is not...
Hi all, I follow example (serial) to build and run, i already run successfully, but i meet some question. when i use generic_on_off to control light at short time(2s), the...
