At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
Hi
We are working on an algorithm applicable to the indoor positioning of ships. We want to improve the algorithm further on top of the existing algorithm for Bluetooth...
I'm on a Comcast cable modem connection. When I've tried to pull up this site over the past few days, I've gotten "The page cannot be displayed because an internal server...
Dear nRF DevZone,
I have question regarding Zephyr k_sleep() function and NRF52840 timers.
I am developing an application for nRF52840 SOC and for that I am using nRF...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to pair from "Settings"-> "Bluetooth" of iOS (iPhone 12 Pro). For pairing...
Hello,
I am developing an application that requires use of some of the traditional C "stdio.h" functionality. My current development setup is the nRF5340 DK running Zephyr...
I'm using sdk for mesh version 5.0.0, sdk version 17.0.2 and my board is nrf52840-DK.
How can i keep mesh config after wake up from deep sleep( system off).Plus, when my...
Hi,
This morning when I tried to access devzone, it says I have been IP banned. I have the same issue as this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/86922...
Currently running NCS 1.7.1, SUPL client 0.7.0 and MFW 1.3.0 it has stopped connecting properly from the last time I've played with it:
Not sure what's up there..
...
I am having trouble powering my uicc. I feel like I am just looking for some setting, but I have not found the right one yet and I am at a loss at this point.
What I have...
I used direction finding rx/tx examples(get 45 points of IQ data). I used the ref period IQ data (8 points) can caculate base phase and the phase velocity(setting is 500KHz...
Dear all,
I have struggled this problem over a week.
I am working on our product, which need to prevent other strangers to connect to our device. After search on the Nordic...
