We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I need nRF52840 revision 3 mounted development kit board, for trial rev 3 's approtect feature. But I don't know when is the rev. 3 mounted development kit board available...
when i make Rx output succefully.i add some configuration in main.c.i can print iq data.there is link that make me to learn to print iq data.
ok,i get iq data in here.but...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
It looks like I can disable the requirement for a signature when downloading an APP or SD (SoftDevice...
I have looked all over the product specification and the website and cannot find any information related to matching an antenna for this device.
What I am looking for are...
Hi I used your nrf toolbox Uart app to communicate from an Android phone to the module to send and receive bytes. The app was automatically updated a few days ago, now i cant...
Hi everyone,
I am not able to connect my J-Link plus compact with the programmer in nRF Connect.
It returns the error Unsupported device. The detected device could not...
Hi,
I am using SGTL5000 CODEC to playback the LINEIN and I am using the SGTL5000 driver from this link
I am using this I2S configuration
For I2S Loopback code itself...
I got an nRF52840 Dongle from someone else and started to see what I could do with it. The problem is, although I've downloaded everything needed including nRF Connect on...
I use: --nrf52840 --nRF5_SDK_17.1.0 --ESB.
Normally, 1:1 communication in one direction is performed from the module with nrf_esb_mode_t = 'NRF_ESB_MODE_PTX' to the module...
Hi,
I'm using the nordic nRF52840 - Dongle and a nRF52840-DK trying to send and write data with the pc-ble-driver-py library.
My problem is that i can communicate in...
Hi DevZone !
I am doing an application with nRF_ESB where I want to send and receive packets through diffenents nodes. Right now, I have 5 nodes, which 2 are repeaters in...
Good Morning,
I started with example ble_app_hids_keyboard for nrf52840 with nRF5_SDK_17.1.0 and I added uart_init() function to use UARTE0 and I modified uart_event_handle...
Hi,
We successfully passed the Verizon self certify program, now onto FCC. I know with the nRF52 series there was a radio test example we ran for FCC; I can't find anything...
Hello, I'm working with board nRF5340 DK. I'm using the peripheral uart0. I want to be able to send data through uart0_tx (P0.22) and to receive the same data through uart_rx...
