We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Here is the main.c file for AES CTR - /examples/crypto/nrf_crypto/aes/aes_ctr example project
'NORDIC SEMICONDUCTORAES&MAC TEST' is the key
Encrypted hex output: "12 DD...
Hi
I have been struggling with increased power consumption after SPI slave usage, and finally seems to have found a solution, based on errata 89.
However looking through...
Dear all,
With nrf9160, I start GPS function.
at#xgps = 1,1
If GPS positioning is successful, I will receive #XGPSP and $GPGGA information. Though I haven't specified...
I’m new to development with the nRF platform and have a general question on using a SoftDevice. A bit of background: in our application we only need BLE for OTA updates and...
Hello, I've tried a few a few combinations of nrfconnect/sdk-nrf branches, but I can't seem to get `CONFIG_CHIP=y` builds to work.
I'm using the following `prj.conf`:
...
I am using tca9548a to connect 8 IMU sensors with a nrf52832 micro controller. I would like to know how to initialize each channel of the i2c mux and how the control to each...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do Thread DFU
I am following https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee...
Hi I'm developing an application using using PWM+ble_app_uart+libuartes. So I have 2 questions 1. I'm using PWM to ring the buzzer a simple melody. What is the example I should...
Hi,
I have used one of the sample and was playing around a write characteristic. I changed the MTU size to 65 bytes and then tried to send same data from the app to the...
Hi,
I am looking for the solution to the following problem while installing the nRFconnect SDK.
$ west init -m github.com/.../sdk-nrf --mr v1.5.1
FATAL ERROR: already...
Hi,
1. Please help me complete example pca10100e_uart
2.I am testing the nRF52820 UART DFU example
3.The example is named pca10100e_uart based on example pca10040_uart...
Need to create Encrypt Image for nRF5340DK board and used Hello-world sample for beginning.
On Enabling BOOT_ENCRYPT_EC256 Kconfig option, I can not compile Hello-world...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I've tried to debug my application in segger embedded studio, I'm getting "No Bootloader was found" error message...
Hi, I'm building an application include ble_app_uart + libuartes + pwm.I merged successfully two 2 examples ble_app_uart + libuartes into an application. So now I need to...
Hello, everyone.
I learned about Bluetooth communication through the example of ble_app_uart. I learned about Bluetooth communication through the example of bl_app_uart...
