We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi everyone, i am developing a system where i have 2 types of board, one board is a central&peripheral (lest name it BOARD1), and the other board is only a peripheral(lets...
Hello!
First of all, thank you for your support.
I'm starting to develop firmware for Nordic chips (I'm a complete newbie). I have been able to compile and download examples...
Hello everybody,
I'm trying to develop simple time synchronization system upon mesh time model, but after sending bt_mesh_time_cli_time_set, first of all my time_update_cb...
NRF52840, SDK, nrf5-sdk-17.
This could be a misunderstanding of how the dual bank update works, however I am finding that after an OTA, Bank0 contains the new fw image but...
I have an SPI sensor that benefits from having a precise clock source, and has a muxed pin that can have a clock source.
The peripheral states that this pin can handle frequencies...
Hi,
We have implemented the DFU Trigger Library on nRF52840 from nRF SDK 15.3 on Application FW. Application is flashed on the device along with Secure Bootloader using...
Hello Nordic team,
I come to you because I face a strange issue during developing a simple feature using PWM.
For a product, I need to make an LED blink smoothly 3 times...
I have a NRF52840 Devkit and also subsequent NRF52840 boards, and I was wondering if there's any WiFi support on them now. I'm aware that it's possible to use any WiFi module...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
I built two...
Hi All,
I'm new to this wireless field. Is there any impact on power consumption based on RSSI level.
As I understand due bad RSSI there will be retries in communication...
I working on Asset_tracker_v2. After going hrough the code, I estimated the work flow to be as:
1. When either Passive or Active state is intialized, the Sample Timer is...
Hi there,
I am running into this error Update CTE params...failed (err -134) while running the direction_finding_connectionless_tx
The output logs are
can I get more...
Hello,
In the product specification for the npm1100 there is an optional battery monitoring circuit schematic on page 39. I'm having trouble understanding why there are...
