We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hey, I'm trying to get a basic BLE with coded PHY (125Kbps) setup with on the fly encryption/decryption working but I'm running into a strange problem. I'm using a custom...
Hi, I want to use the nRF9160 in a project, where I need the antenna attached to the nRF9160 to be able to handle being 1000m below the sea-surface. It is an AUV that collects...
Hello,
At present, there is a problem. When there are a few broadcasting devices nearby but many active scanning devices that the active scanning is not easy to find devices...
Hi
I am using app_timer_cnt_get() like MIllis()
uint32_t millis() { uint32_t milli; milli = app_timer_cnt_get() /32.768; return milli; }
but when i connect the nrf52840...
Hello ,
i have successfully compile and run 'binky' and 'Hello_words ' sample code using segger .Now i want to test Uart communication with nrf9160 . (want to send string...
Hi,
we are following below link for DFU example i.e. serial dfu on nRF52833. we are not able to install mcumgr in windows . are we missing anything here. kindly help us...
I'm testing an implementation of the serial UART bootloader for DFU. Firmware update using nrfutil works fine, using a serial-USB dongle, The only issue I'm seeing is that...
Hi DevZone,
I have recently updated:
nRF5 SDK to 17.1.0 from 15.3.0
S140 to 7.2.0 from 6.1.1
SES to v6.20a from 4.16
The SoftDevice now fails to initialize when...
hi support team,
in ncs llpm example, we tested it and find out one problem, why 4bytes of timer data would spend more than 1ms? please see picture 1.
further more,
...
I testing asset_trcker_v2 and want to add new custom event module. I have few doubts and queries:
1. There is event_handler function in each module as well in main fuction...
Hi,
I am working on the nrf5340 with zephyr (NCS 1.7.1), I need to monitor the voltage of the battery, in the beginning, I used the ADC API of zephyr, and it works well...
Currently I have a 52840 peripheral running peer manager. We bond/peer with it using a passkey system from an mobile phone central. It works great.
SDK is 1702 nrf5.
What...
I wanted to confirm that on the nRF9160, it is acceptable to tie the VDD and VDD_GPIO pins to the same 3.3V rail and bring them up together. The VDD_GPIO rail will not be...
