We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I want to build a wireless split keyboard (Left and right parts). I want them to connect to one PC but only need to establish the connection one time. Can both part...
I am working on ble mesh with sdk17.0 and sdk5 for mesh I want to send large data vai ble mesh I followed this post https://devzone.nordicsemi.com/f/nordic-q-a/71105/sending...
Hello.
I've a ublox module with nRF52811 chip.
Is it possible to make a BLE beacon receiver with nRF52811? If yes, is there any demo application? I've searched nRF SDK...
I have been playing with an Ikea Tradfri E1812 button, a Philips Hue bulb, and zigbee2mqtt. I see that when I bind the button's OnOff output cluster to the bulb's OnOff input...
nRF52804 SPIM3 not work. (SCLK/MOSI not output)
However, if I debug it using jlink, it works.
My environment is nRF52840-DK(PCA10056/v1.0.0) nRF52 SDK 17.0.2
My program...
Hello,
I am looking into evaluating the nrf5340 with different functions running out of external flash, and how current draw is affected by these functions. We are looking...
Hi All,
I am working on NRF52840 and trying to optimize the BLE throughput. The current settings are:
PHY: 2M PHY
Conncetion Interval: 9.375 ~ 15 ms
GAP_DATA_LENGTH...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
Hi Everyone,
I hope you all are well.
I'm using nrf Connect SDK v1.7.0 and VS code for nrf52833 chipset.
So far I've used NUS service in my code to transmit some data...
Hi, I am trying to write an "event dispatcher" so it's possible to listen to types of event and send events. You pass a function pointer and it will be called when that event...
I was gone for a bit came back did my updates and I can't program my boards threw nRF connect anymore. They just don't show up so reinstalled everything many times restarted...
I am using Zephyr development environment for BLE application development on my computer, now I need to use nrfjprog when burning in (flash), my question is whether nrfprog...
hello sir,
i am using segger to program nrf9160 . i have successfully uploaded sample sketch for blink led using "" open NRF Connect SDK " option. Now i want to create a...
Hi,
We have a custom bootloader and a firmware, both use the USB CDC ACM. Is it possible to start the firmware without resetting the USB instance so Windows have a continuous...
Having done a completely fresh install of nRF Connect v3.7.2 for macOS (s recommended by Nordic Support due to known issue with Programmer), and installed both the latest...
