We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
In SDK 1.9.0 i saw that QSPI deep power down was implemented and i can confirm that that works using the below code. The issue I see is that if the device is in deep power...
Hi,
Is there any sample/example that comes with SDK that shows how to add extended data in BLE advertisement (using Zephyr)?
I have tried adding some additional bytes...
We have 3 nRF52840 to establish a net. one for master device, One for Master device, One for HUB(Msater-Slave) device, and One for Slave device. The data flow is Slave device...
Hi,
Following the update of my mac (M1) in Monterey, i can no longer flash programs on my board (everything worked under Big Sur).
I got the error JLinkARM DLL load...
Hello,
I am currently trying to add a FEM (nRF21540) to an already existing BLE project that is using nRF5 SDK. For that purpose I ordered the nRF21540 DK that is using...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now my customer ask me if it possible to have the LQI value...
Hi,
My goal is to use a timer to trigger SPI transactions and the spi_event_handler() to trigger bluetooth transfers. In order to make it as fast as possible, I would...
Hello, we're trying to make products using BLE with nRF52840(central) and nRF52833(peripheral).
We did make custom boards and also made a program that once paired(bonded...
Hi all,
I'm working with a pressure sensor (LPS22HBTR) and the nRF52-DK and I have some issues when sending data through BLE (nRF52832). When I run the program without...
I have recently upgraded from NCS 1.5.0 to 1.8.0 and noticed that the native TLS stack (vanilla mbedtls) was no longer being used for TLS based sessions.
My use case requires...
Hi,
I found the online power profiler for BLE ( Online Power Profiler for Bluetooth LE - opp - Online Power Profiler - Nordic DevZone (nordicsemi.com) ), it helped me to...
I was working with VS code just fine and then upon booting it up today suddenly nothing will build anymore including sample projects. the only thing that i could tell that...
hello Nordic
i am working with nrf52840, with zephyr 2.6.9, ncs 1.7.1
i want to have an interrupt on a pin toggle and have a callback for up and one for down
i configure...
