We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Using nRF5 SDK v16.0.0 on nRF5232. IDE = SES
When advertising is started, I want to advertise initially for 30 seconds, so I set APP_ADV_DURATION to 3000, and the device...
Hi,
I'm developing a project with nRF52832 and BOSH BME688 sensor.
I downloaded the library from github to use the sensor (here it is the link https://github.com/BoschSensortec...
I'm working on an nrf52840 dk. I need to print the sensor data on the command line. I've added the sensor config to the prj.conf file as well as the sensor and sensor_shell...
Hello, Support
I am looking for AT Command example running on nRF52833, host interface is UART interface , and the SoC will be running like a AT Client?
Could anyone help...
I tried to work the zephyr MPU6050 out of the box but it returns "failed to find sensor MPU6050". I can't seem to find a solution to this. The overlay and prj.conf file were...
Hi!
I am working with an nRF5340.
- Is it possible to somehow fill an array with values read from a GPIO OUT register using DMA or PPI?
- Is it possible to assign...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
By default, CONFIG_ZBOSS_OSIF_LOG_LEVEL_CHOICE was set to ZBOSS_OSIF_LOG_LEVEL_INF. But I'd like to increase the log level to debug a problem I'm seeing. When I increase verbosity...
Whilst I recognise some of the NC pins on the nRF52833 are IO pins on the 52840, but I also noticed apin mapping difference on a common port...52833 A16 is P1.05 and whilst...
We are using SDK 15.3.0 and S140 v6.1.1 SoftDevice. We are using an external LF crystal with tolerance of +/-20ppm, and are therefore using
#define NRF_SDH_CLOCK_LF_SRC...
Hi,
As per this link , the memory requirement of Thread 1.2 based application in nRF Connect SDK is around 487KB, over which more will be added as per application development...
I flashed a nrf52dk - nRF52832 board with a sample project (peripheral_hr) and the name is displayed correctly in the nrf connect app and other BLE discover apps.
After...
I need twoADC channels. I tried to configure using :
CONFIG_ADC= y in prj file,
&adc{ #io-channel-cells = < 0x2 >; }; in overlay file .. the compile error appears as shown...
HI
I am using VS for the firs time and I am trying to build the project Blinky but when I try to add the blinky folder to applications to build I get
: Element with id...
Hi ,
I followed the DFU-OTA tutorial(DFU over Bluetooth) given below for nrf52833dvk. and it is successfully completed. Now the query is , once we shared the bin file from...
