We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
The ZB_ZCL_VERSION define in the file zboss_api_zcl.h have a bad value in the SDK NRF 5 v4.1.0 In the documentation, it is mentioned that :
The Nordic Zigbee software...
Hi!
I did a mesh trying to use diferent versions of a project renaming them, deleting the files inside the folder where I have my projects, putting inside other projects...
We're using nrf Device Manager for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and the out-of-the-box Zephyr...
Why there are multiple resets after post validation, firmware activation, etc in firmware update process? Can it not be handled sequentially without resets?
Hi,
We are trying ble_app_uart example for nRF51822 with nRF5 SDK v12.3 and ble_app_uart_pca10028_s130.hex file provided from hex folder works fine, but when we open IAR...
Central nRF5 device connects to peripheral NCS and initiates bonding.
The peripheral reports that security failed with error code 4 (BT_SECURITY_ERR_AUTH_REQUIREMENT) "The...
Hi all,
I am a beginner of nRF5340, trying to test AoA function for indoor positioning.
I'm wondering if there is any helpful document that goes through the whole process...
Hi there,
We are developing on the NRF5340, and have a question regarding programing. You cannot program a core, while Nordic is only powered by Vbus. When I give Vbus power...
Hi,
I have a idea but at the moment not the right approach to do it, thats why I ask here.
I want to store the current time somehow on the device so it survives a reboot...
I am working in a project where we want to be able to do full modem firmware update with FOTA for modem version 1.3.x. According to the release notes, in order to do this...
hi, i am using ncs 1.8.0 for an application where i need to send some data every 10 ms. directly sending data over NUS with bt_nus_send() from the main thread works fine....
While trying to debug some issues with my board I accidentally programmed by custom board while powering it with only 3V and now whenever I try programming it I get the following...
I want to send some data to client from server when I received data from client using server_set callback function.
Means I want to reply to client some other data then...
Hi Nordic,
I am using SDK 15.3. While I am working on a central, which connects 2 periperial devices simultaneously, I found a id_manager.c issue, protentially a bug I guess...
