We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi again
I have used nrfConnect to create an application from sample, the sample being peripheral_hr_coded
I have placed my custom service into the app, and it works...
Hello, I am trying to measure the input voltage on an nRF52833 and it is not behaving as expected.
The following code is taken from here and works as expected on any nRF52832...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
Hello,
I would like to use littlefs in out Project and it seems to be very usefull. I read several documents and have the sample running on the eval board. But there is...
Hello,
I'm using the power profiler to perform current measurement of our IoT device. It appears to work well when running for a few minutes capturing. When I wrong for...
I am trying to use SPIM2 on an NRF52840 based board. The SDK is 17.0.2.
For the life of me I cannot understand how to 'consistently' determine the values to be specified...
I'm trying to modify the HTTPS sample to connect to Google Cloud Functions but I keep running into this issue where connect would fail.
1. I have disabled TLS peer verification...
We have a running project with nRF52840 + S140 7.2.0 - SDK: 17.0.2 + Bootloader.
I need to change the size of our bootloader in a production environment. This update must...
Hello,
We are currently certifying our module for Verizon in the US. As such, we are updating our software to work with MFW v1.3.0 and the corresponding NCS version v1...
Dear Nordic,
we developed firmware based on S112 and SDK 17.1.0. We have a problem with poweroff routine: at poweroff the status LED is ON.
this is part of our circuit...
Hi Team,
I am using nRF52840 on our custom board. I have enabled SMP for DFU and SMP image management in my build. DFU was successful for the 1st time but when I try to...
