We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
Code is based on Nordic UART Service Client sample on nRF Connect SDK v1.8.0
I am trying to create several client connections for different servers. The code is incomplete...
Hi Nordic team
I tried SDK Connect v1.8.0 ble_peripheral_lbs_coex sample.
It found advertising signal was very weak. The distance between PCA10112 and my phone was 1 meter...
I use PPI for ADC and GPIO pulling. When I connect and then disconnect - nrf52840 not advertise until reset the SoC.
I can connect after reset. But when I disconect then...
I am used to using Segger, but am switching to west for various reasons. The main reason is to create a CI/CD pipeline.
I built a sample project with west, didn't see any...
Hello,
I am new to embedded/BLE development so forgive me for my ignorance on some of these topics. I am creating a fairly simple BLE Peripheral Server device that has a...
I have built and run the application: Asset Tracker v2 using Segger IDE with nRF Connect SDK 1.8.0 , and my nRF9160DK device communicates with the AWS IoT Core topics.
I...
Hello Team,
I have interfaced Oled with NRF52805 on i2C.
I have used SDK 15.1.0. and ble_app_uart example [s112].
My problem :
I have made some customized functions...
Hi everyone,
I'm using SEGGER Studio for development. I wrote a code for accessing Flash memory by modifying flshawrite example in SDK.
Now I want to copy all dependencies...
