Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
we use nRF52833,SDK:S140,17.2,sometims,the device goes into trouble and the error code is 0x715.
here is the call stack:
/port.c:128 0x00027482 PendSV_Handler
/port...
When developing a BLE device with nRF52840, the following error occurred when importing the header file for spi communication.
ERROR ['NRF_DRV_SPI_INSTANCE_0' undeclared...
I am using FreeRTOS with FatFS/SD card. SDK is nRF5_SDK_17.0.2.
If different tasks access FatFS API in different task, is it thread-safe? i.e. Task A access file A and task...
Hi,
I'm integrating the ble_app_uart example into my project. However, the UART interrupt works a little differently than I expect. I initialized the UART with APP_UART_FIFO_INIT...
Hello
I followed the doc blew for building sample
- https://infocenter.nordicsemi.com/topic/ug_gsg_ses/UG/gsg/intro.html
- https://devzone.nordicsemi.com/nordic/nordic...
Hi,
Currently I have a NRF52832 chip that I am using in a project. The chip is inaccessible since it is inside a device -- I have been performing software updates via the...
I've mistakenly closed the case https://devzone.nordicsemi.com/f/nordic-q-a/85450/insufficientresources-error-message-while-performing-usb-dfu?ReplyFilter=Answers&ReplySortBy...
Hi
I'm working with the sample 'ncs1.7.1\nrf\samples\bluetooth\direction_finding_connectionless_tx' on nRF5340, I followed this page and built with AoA mode, then added...
Hello,
I am referring to the ISP4520 example code .
I would like to change the I2C(TWI) pin assignments as below.
SCL:P0_07 / SDA:P0_12
But I can't find where to set...
SDK 17.1.0
nRF52840 DK central + nRF52840 peripheral device
Hello,
I'm attempting to set up reading characteristic values on the nRF52840 DK as a central from a peripheral...
hi,
We are currently having some problems erasing flash，The problem recurrence rate was 1%，the recurrence rate of specify chip problems is 100%，Here are some scenarios as...
Hi,
In secure_bootloader(SDK17.1.0) example, I want to replace the ECDSA_P256_SHA256 with ED25519, what should I do?
I tried to modify sdk_config.h, but the build didn...
I have the EV BT-840 DK and I have the AT firmware installed. With AT commands I am able to connect and send data to other BT-840DK. Right now I flip the AT command switch...
Hi Guys, I am following the numbers and tutorials and setting up Visual Studio on a windows PC and installing the Nordic extensions. I get as far as a successful build but...
I was able to work with the mfrc522 RFID card reader through SPI on nRF9160dk. The application was developed using connect SDK v1.5.1
When we tried developing using SDK...
