Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
Hi everybody,
I saw topics with similar naming like mine, but none of them actually describes my issue.
I develop some simple scanner and advertiser solution.
...
software:nrf connect sdk 1.9.1
hardware:nrf5340
hi professor,
I use the nrfx_gpiote_in_init(GPS_TS_PIN, &config_in, gps_timepulse_handler) but return NRFX_ERROR_NO_MEM...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I am considering adding the following bootloader to my project. nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader...
Hello Nordic：
I wanna to know what actions a thread have done from reset to joined a thread network.
I observed the air packets by using Wireshark. I found a router(rx_on_when_idle...
The device is connected to the PC via FTDI chip. The device manager shows the COM port. LTE Link Monitor v2.0.1 cannot find the connected device on SELECT DEVICE. The windows...
Hello.
I am using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral and developing.
I am using nRF Connect to communicate with the peripheral nRF52832.
One of the...
Hi,
I have tried to follow the below tutorial ( https://www.youtube.com/watch?v=hY_tDext6zA&t=933s) . While I am trying to advertise the ble by following that webinar. I...
Hi,
I want to use BLE as both connectable mode and non-connectable mode in the same application. Is it possible to do that?
Is it possible to switch connectable BLE mode...
Hello!
I have a nRF52840DK with a custom board. I have installed nRF 1.9.1. I have read about the twi_scanner but I don't find that code in my installation! Did I do anything...
Hi,
I am trying to download SUPL client library but got an email that my request was denied. I've used the same email address as the one here. Can you please advise?
Kind...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i need help.
We use nrf52840 and DK17.0.2
Using saadc with oversampling x8 , Single-ended mode.
Question
When Event monitoring using limits , Is the timing at which...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
