Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
We are using nRF9160 chip (in own custom board), SDK 1.9.1 board with "serial lte modem" firmware. We are unable to get coordinates using AGPS. I suppose this is due to the...
Hi!
I am going to use nRF52832 in a new product and wondering whether should I base an application on the new or the old SDK. I have to take into account support for DFU...
Hi,
recently I got Thingy:91 (board info - PCA20035 1.4.0 2020.22),I've updated it to the latest firmware as per instructions. So far so good. Then I started playing around...
I tried to create/ open a project using nRF Connect in SES. The error appears as shown in image. While the file exists as shown in the second image. Why, such error and what...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
I'm running into a weird bug where the first 4 bits received by my SPIM are always 1 - the next 64.5 bytes are all correct though... I've built 3 FWs out of provided examples...
Hi guys,
I have developed an app to read data from some sensors and notify the central with a frequency of 100Hz. It seems to work but I would like to share my approach...
Hello,
We are trying to get UART communication between nRF9160 and MSP430.
MSP430 need to send out a sensor data through UART.
We are using 1.9.1 SDK, and Visual...
